Industrial sourcing · China to Europe

Buyer-firstOpen route · visible proof

Buyer guide · Electronics & assembly

Dispensing robot from China

A dispensing robot is mostly its valve and your fluid: the axes are the easy part, and a quote that names the robot but not the valve leaves bead size and repeatability open.

Ask about this machine ↗Where the numbers come from

Written and listings checked 30 September 2026. Every figure on this page names its source.

What you are actually comparing.

Two quotes, one machine name

What hides inside the price

Valve type

Time-pressure syringes are cheap but drift as the syringe empties. Auger, jet and volumetric valves hold dot size better. Ask which valve is quoted and what it costs to change.

One-part or two-part fluid

Two-part epoxies and silicones need a meter-mix valve and a purge routine before the mix cures in the nozzle.

Desktop, vision or arm

Seven of fourteen listings we checked were desktop three or four axis units; two added camera vision to find parts; three were six-axis arms. Vision matters when parts do not sit in the same place twice.

Stated accuracy

None of the fourteen listings stated a repeat accuracy. Get it in writing, with the method used to measure it.

Before you ask for a price.

Send these with the enquiry. Without them, any number a factory gives you is a guess dressed as a quotation.

Fluid by maker and product, with viscosity and pot life.
Dot or bead size, and path drawing on your part.
Parts per hour and how parts are located.
Working area needed.
Whether you also need curing, heating or mixing.

Turn the claim into a demonstration.

Require this	A pass looks like
Dispense a counted batch on your parts with your fluid.	Dot or bead size measured on samples and inside your tolerance, results recorded.
Weigh shots at the start and end of a syringe or cartridge.	Shot weight stays inside your tolerance as the reservoir empties.
Pause for your longest break, then restart.	No blocked nozzle or first-shot defect after the pause.

The documents that must arrive with it.

EU Declaration of Conformity citing 2006/42/EC, or Regulation (EU) 2023/1230 for delivery from 20 January 2027, plus Low Voltage 2014/35/EU and EMC 2014/30/EU; for six-axis arms, the risk assessment referencing EN ISO 10218.
Manual in your language with valve settings and cleaning steps.
Valve spare parts list with seals and nozzles.

The one people forget. The valve seal kit part numbers. Seals wear with abrasive fluids, and a seal from the original maker takes weeks to arrive.

When this is the wrong machine.

Buy something else if

Named, not hedged

You coat whole boards with a thin protective film.

A conformal coating machine with spray valves.

You dispense solder paste on boards in volume.

A solder paste stencil printer.

Where the numbers come from.

We name the kind of source, how many and when, and never the factory. Listed prices are asking prices, not landed cost. Where we do not hold a fact we say so: that is a GAP, not an estimate.

Listings · 14Fourteen marketplace listings for glue dispensing robots, checked September 2026: seven desktop three or four axis units asked US$1,980 to US$6,000, two with camera vision asked US$5,000 to US$7,000, and three six-axis arms asked US$6,999 to US$31,600; none stated a repeat accuracy. Asking prices, not landed cost.
GAPGAP - no supplier quotations logged for this machine yet. Three to five quotations for one configuration would give a real price spread.

Related machines.

Conformal coating machine. Choose a conformal coating machine to protect whole boards with a thin film.
Automatic screwdriving robot. Choose a screwdriving robot when parts must come apart for service instead of being bonded.

Every machine we source in this area is on the Electronics & assembly page. How a project runs, stage by stage, is on how it works, and what it costs is on pricing.

Straight answers

Questions buyers ask about this machine.

Chinese vs European dispensing robot?+

Desktop axes are similar. Valves differ most, so you can ask for a quote with a valve you already trust fitted to the robot.

What goes on a dispensing robot inspection checklist?+

The three tests above and a check that programs can be edited offline.

What CE documentation does it need?+

A Declaration of Conformity, technical file and manual in your language.

Who is the EU importer?+

Your business if it brings the robot in: your name and address on it.

Contact

Tell us what you need.

Send a machine, a quotation you want checked, or a question. We reply with what we would look at first.